•
•
•

•

Soft non allergenic silicone Conforms to workers face Even seal without creating pressure points   The low profile of the 7700 series gives wearer a   wide field of vision and room for protective eyewear.  

The low inhalation and exhalation resistance makes breathing easier, leaving more energy for production.

Cartridges, filters, pre-filters and filter covers must be ordered separately

•
•
•

•

Silicone Full face-piece Lightweight design

Designed to cover workers face in full Meets OSHA requirements  

The 7600 Series full facepiece respirators are designed to provide eye, face and respiratory protection while providing optimum comfort.  

Cartridges, filters, pre-filters and filter covers must be ordered separately

Available replacement parts ensure that the unit is not made unusable should one part become worn or damaged.

1. AS154377 Filter Connector
2. AS154512 Inhalation Valve
3. AS154555 Exhalation Valve
4. AS263761 Lens Clamp Set
5. AS263761 Lens Clamp Set
6. AS263699 Valve Seat, Inhalation
7. AS263702 Oral Nasal Cup Med / Large
8. AS263613 Basic Facepiece Med / Large
9. AS263621 Lens Clamp Screw
10. AS263648 Lens Clamp Nut
11. AS263656 Headstrap
12. AS263664 Latch
13. AS263672 Bail
14. AS222828 Replacement Lens
15. AS263680 Flange
16. AS263710 Locking Nut
17. AS263729 Speaker Diaphragm
18. AS283274 O-Ring

19. AS283274 Speaker Adapter
20. AS263745 Gasket
21. AS231657 Nut Adapter
22. AS212172 Valve seat, Exhalation
23. AS212180 Exhalation Valve, Guard
24. AS263753 Grommet

Please Note: Items not listed in the table have a delay period for shipping.
Please contact your Saint-Gobain Abrasives customer service representative for any additional information. 

•
•

•
•

•

•

Lightweight design

Filters or cartridges suspended on workers back Silicon facepiece material Meets OSHA requirements Excellent fitting resulting in better worker protection   The air purifying elements are suspended on to   the worker's back via two flexible breathing tubes, holding the air purifying cartridges or filters away from the work zone where there are higher concentrations of contaminants.   The result is longer service life for the cartridges and filters.

Cartridges, filters, pre-filters and filter covers must be ordered separately

•

•

•

•

Colour coded for easy identification

All respirators approved to the New NIOSH 42CFR84 Regulation

Durable sonic-sealed plastic construction Filters and cartridges have an inside threaded section Universal design  

When cartridges are not stored properly in the work area i.e. in a sealed plastic bag. Cartridge life will be significantly reduced, as the cartridges will continue to adsorb the contaminant.

•

•

•

Prefilters are designed to prolong the life of cartridges by filtering out the larger particles of containment

They are held in place with a Fit Check Filter Cover

Use 7500-6 Dusts and P1 Mists Use 7500-10 for paint sprays and P2 mists

•
•

•
•

•
•

•
•
•

Lightweight and durable Disposable Cushioned nose piece

Large filter area Strengthened outer shell Steel formable nosepiece Compact design

P1 Grade

•
•
•
•

•

•

•

•

Suitable for welding Exhalation valve

Disposable Lightweight Large filter area

Steel Formable nosepiece Compact design  

The 1955 Dust / Mist Respirator gives workers a greater comfort especially under hot or humid conditions.  

There is no expensive maintenance program required as this product is disposable.

•
•
•

•

•

Lightweight and disposable Easy to use Easy dispensing  Foam Construction Sealed plastic pouches  

Norton DeciDamp ear plugs are designed to provide maximum comfort while in use.  

They have been tested to ensure that they expand smoothly, attenuate hazardous noise levels and allow the best fit in virtually any workplace where hearing protection is required.

•

•

•

•

•

•

Light weight plastic case for hygienic storage

Striking Colour for easier identification

Earplugs case can be attached to a key ring   Effective in blocking out both low and high frequency noises  

The Com-Fit Earplugs are multi purpose with comfortable wear because they are made of soft pliable silicone rubber.  

They are non-toxic , non-allergenic and will not shrink or harden when exposed to ear wax or skin

•
•
•
•

•





•

•
•


•
•

•

Worknit and Worknit HD Gloves Worknit gloves are nitrile coated to provide excellent resistance to cuts abrasions and slashes Grip-N Hot Mill Gloves Heavy Duty cotton gloves Suitable for 200ºC

Nitri-Guard Gloves Heavy duty Kevlar/cotton gloves designed to resist abrasion Suitable for 200ºC